Zhone-IMAC

Sort By:  
8901
$700.00
890220
$1,000.00
8905
$700.00
890620
$500.00
8907
$1,000.00
891630
$1,100.00
891830
$1,500.00
891930
$2,000.00
892060
$1,800.00
892260
$3,000.00
892360
$2,200.00
892460
$2,000.00
892560
$1,200.00
893270
$3,000.00
893370
$2,200.00
893470
$2,000.00
880060
$1,500.00
880160
$4,000.00
880370
$4,300.00
880460
$2,200.00
8901 (AC Power Supply, 120/240VAC, CE marked)
Main power supply for AC powered IMACS units. 120/240VAC, 50-60Hz input provides +/-5V and +/-12V. Can be used with 8905 Power Converter to provide -48VDC from either 120VAC or 240VAC. A second 8901 may be installed for load sharing/redundancy.
8901
$700.00
890220 (DC Power Supply, -48VDC, CE marked)
Main power supply for use with external -48VDC sources. Provides +/-5V and +/-12V. Includes low input voltage alarm at -42VDC or less. A second 890220 may be installed for load sharing/redundancy.
890220
$1,000.00
8905 (Power Converter, 120/240VAC to -48VDC, 100W, CE marked)
Used with 8901 with either 120VAC/240VAC, 50-60Hz input to supply -48VDC system voltage. Optional redundancy of the 8905 is supported in the IMACS 800 and 900 chassis only. Consult Zhone GSS if using with negative ground.
8905
$700.00
890620 (Ring Generator, -48VDC)
Used to supply ringing current for all FXS cards and for FXO cards in manual ring down applications. Provides control of in-rush current during startup and hot insertion.
890620
$500.00
8907 (Power Supply, -24VDC, CE marked)
DC main power supply for use with external -24VDC sources. Provides +/-5V and +/-12V. A second 8907 may be installed for load sharing redundancy. Consult Zhone GSS if using with negative ground, or if +24V is required. Cannot be used with 890620 ring generator.
8907
$1,000.00
891630 (IMACS 600 Chassis, CE marked)
Steel chassis, front loading, "V" steel card guides; with installation kit. Provides 2 CPU slots, 8 universal slots and 1 interface slot. Universal slots can support up to 3 server cards and up to 4 WAN cards. All universal slots not allocated to servers or WANs can be used for user cards. Accommodates 1 main power and 1 redundant main or 1 main power and 1 AC/DC converter and 1 ring generator. AC and dual DC inputs. NEBS compliant.
891630
$1,100.00
891830 (IMACS 800 Chassis, CE marked)
Steel chassis, front and rear loading, "V" steel card guides; with installation kit. Provides 2 CPU slots, 3 server slots, 4 WAN slots, 1 interface slot, 8 user slots. AC and dual DC inputs. Two slots for main power supplies, 5 separate slots for -48VDC converters or ring generators. CPU, WAN, server cards and power supplies load from front. User, interface cards, ring generators and voltage converters load from rear. NEBS compliant.
891830
$1,500.00
891930 (IMACS 900 Chassis, CE marked)
Steel chassis, top & bottom front loading, "V" steel card guides; with installation kit. Provides 2 CPU slots, 3 server slots, 4 WAN slots, 1 interface slot, 8 user slots. The power section on top has two slots for main power supplies and 2 slots for -48VDC converters (8905) or ring generators (890620). AC and dual DC inputs. All system components load from the front. When used with an external -48VDC power supply, the 891930 chassis allows for the power requirements of having up to 7 BRI cards installed. NEBS compliant.
891930
$2,000.00
892060 (Interface card, 8 T1/E1 ports, 2400bps modem, 32K NVRAM, CE mark)
Physical interfaces for up to 8 T1/E1 lines on single 50 pin Amphenol connector, integral V.22bis modem and port (RJ11). VT100 control port (RJ45), DB9 computer port for connection to network management system and nodal port (RJ48) provides 1 alarm output to external reporting device. Can be used with all system releases up to and including v3.x.y. This card is being manufacture discontinued. A last time buy is in effect.
892060
$1,800.00
892260 (Interface card, 8 T1/E1 ports, no modem, external sync (framed T)
Physical interfaces for up to 8 T1/E1 lines on a single 50 pin Amphenol connector, VT100 control port (RJ45), DB9 computer port (COM 1) for connection to network management system and RJ48 computer port (COM 2), RJ45 for external sync connection and node port (RJ48) provides 1 alarm output to external reporting device. Use with 5.x.y or 6.x.y CPU firmware.
892260
$3,000.00
892360 (Interface card, 8 T1/E1 ports, 2400bps modem, 128K NVRAM, CE mar)
Physical interfaces for up to 8 T1/E1 lines on a single 50 pin Amphenol connector, V.22bis modem and port (RJ11), VT100 control port (RJ45), DB9 computer port for connection to network management system and node port (RJ48) provides 1 alarm output to external reporting device. Use with 5.x.y or 6.x.y CPU firmware.
892360
$2,200.00
892460 (Interface card, 8 T1/E1 ports, no modem, 128K NVRAM, CE marked)
Physical interfaces for up to 8 T1/E1 lines on a single 50 pin Amphenol connector, no modem, VT100 control port (RJ45), DB9 computer port for connection to network management system and node port (RJ48) provides 1 alarm output to external reporting device. Use with 5.x.y or 6.x.y CPU firmware
892460
$2,000.00
892560 (Interface card, 2 T1 ports, no modem, 32K NVRAM)
Two RJ48 and bantam jack connectors for T1 or balanced 120-Ohm E1 lines. VT100 control port (RJ45). No DB9 computer port. Can be used with system releases up to and including v3.x.y. This card is being manufacture discontinued. A last time buy is in effect.
892560
$1,200.00
893270 (Split Interface card, 8 T1/E1 ports, no modem, external sync (fr)
Physical interfaces for up to 8 T1/E1 lines on a single 50 pin Amphenol connector, VT100 control port (RJ45), DB9 computer port (COM 1) for connection to network management system and RJ48 computer port (COM 2), RJ45 for external sync connection and node port (RJ48) provides 1 alarm output to external reporting device. Logical interfaces separated from WAN inputs, supports card replacement without causing system outage. Enhanced panel fasteners. Use with 7.x.y CPU firmware.
893270
$3,000.00
893370 (Split Interface card, 8 T1/E1 ports, with modem, CE marked, use)
Physical interfaces for up to 8 T1/E1 lines on a single 50 pin Amphenol connector, V.22bis modem and port (RJ11), VT100 control port (RJ45), RJ45 computer port (COM 1) for connection to network management system and node port (RJ48) provides 1 alarm output to external reporting device. Logical interfaces separated from WAN inputs, supports card replacement without causing system outage. Enhanced panel fasteners. Use with 7.x.y CPU firmware.
893370
$2,200.00
893470 (Split Interface card, 8 T1/E1 ports, no modem, CE marked, used)
Physical interfaces for up to 8 T1/E1 lines on a single 50 pin Amphenol connector, VT100 control port (RJ45), RJ45 computer port (COM 1) for connection to network management system and node port (RJ48) provides 1 alarm output to external reporting device. Logical interfaces separated from WAN inputs, supports card replacement without causing system outage. Enhanced panel fasteners. Use with 7.x.y CPU firmware.
893470
$2,000.00
880060 (CPU card, BCON bus-connect, Host 3.x.y., non-redundant, 2 T1/E1,)
The 880060 is the base model CPU card, with Supports 1 WAN card for a total of up to 2 E1 or T1 WAN ports (on separate WAN card). Does not support cross connect module or redundant CPU operation. WAN card must be installed in slot W1. Can operate in termination or drop and insert mode. CPU card also houses voice signaling firmware (included) and optional SNMP and/or TR-08 management firmware (must be ordered separately). CPU Host firmware must be ordered separately. Can be used with system releases up to and including v3.x.y. Requires appropriate interface card (892060, 892160 (MD announced), 892560, 892660 or 892760). This card is being manufacture discontinued. A last time buy is in effect.
880060
$1,500.00
880160 (CPU card, XCON cross-connect, Host 3.x.y., redundant capable, up)
The 880160 supports complex applications requiring more than 2 WAN ports and the ability to cross-connect DS0s between WANs. Supports up to 4 WAN cards for a total of 8 T1 or E1 WAN ports and has a built-in cross-connect module. Two model 880160 CPUs can be installed for CPU redundancy. 1:N WAN redundancy is also supported. CPU card also houses signaling firmware (included) and optional SNMP and/or TR-08 management firmware (must be ordered separately). CPU Host firmware must be ordered separately. Can be used with system releases up to and including v3.x.y. Requires appropriate interface card (892060, 892160, 892560, 892660 or 892760). This card is being manufacture discontinued. A last time buy is in effect.
880160
$4,000.00
880370 (CPU card, XCON cross-connect, Host 6.x.y., redundant capable, up)
The 880370 supports complex applications requiring more than 2 WAN ports and the ability to cross-connect DS0s between WANs. Supports up to 4 WAN cards for a total of 8 T1 or E1 WAN ports and has a built-in cross-connect module. Two module 880370s CPUs can be installed for CPU redundancy. 1:N WAN redundancy is also supported (with relevant WAN card options). CPU card also houses voice signaling and SNMP management firmware (included) and optional TR-08 firmware (60102) (must be ordered separately). Requires v6.x.y CPU firmware (must be ordered separately). Requires appropriate interface card (892260, 892360 or 892460). This card replaces the 880160, 880360, and the 880361.
880370
$4,300.00
880460 (CPU card, RCON bus-connect, Host 3.x.y., redundant capable, up t)
The 880460 CPU supports 2 T1 or E1 WAN links in slot W1 with a redundant card (similarly configured) in slot W2. WAN ports in slot W1 may operate in drop and insert or terminate mode. The 880460 supports another 2 T1 or E1 WAN links in slot W3 with a redundant card (similarly configured) in slot W4. WAN ports in slot W3 can only operate in terminate mode and can only be used to support 820260, 821360, 821560 or 821570 HSU card ports and 824160, 824660 and 8249 OCU-DP ports. CPU Host firmware must be ordered separately. Can be used with system release up to and including v3.x.y. Requires appropriate interface card (892060, 892160 (MD announced), 892560, 892660 or 892760). This card is in Limited Availability status.
880460
$2,200.00
Per Page      1 - 20 of 194